GSM Network Autodiallers and Interface Units

GSM Voice and Text Autodialler
GSM Autodialler

Low cost GSM autodialler, which delivers a pre-recorded voice message upon activation

Add to most alarm control panels and external equipments

All programming via keypad.

Dual triggers with the ability to dial up to 9 x 32 digit telephone numbers per trigger - 10 second recordable message per trigger

Programmable time delays for the dialler to become active after arming and for the dialler to dial out after triggering

Option to activate a built in sounder and to cancel both dialler and sounder from remote telephone

Requires either a pre-paid or contract SIM card - will operate with most SIM cards Auto-dialler dimensions 200 x 120 x 45mm

 

Kit contains:

  • 1 x GSM Auto-dialler
  • 1 x Fixing kit and installation & programming guide
  • 1 x rechargeable 7.2V battery

Operating voltage 12 volts d.c.


Click for GSM Network Autodialler Technical Manual
 
 

GSM 4 number Voice and Text Autodialler

GSM Voice / Text Message Alarm Communicator / Autodialler

The GSM Voice Alarm Communicator (GSM-VAC4+LITE) is an inexpensive and reliable device that transmits pre-recorded speech messages and / or SMS text messages, on alarm, to up to 4 different telephone numbers.
The GSM network is used for the transmission and is especially suitable for locations where transmission is not possible via fixed telephone or an additional signal path is required. It has 2 alarm inputs. When an input is activated it automatically dials out to preprogrammed numbers and an alarm message is sent.
GSM-VAC4+LITE also has 2 outputs to control devices remotely.

 

DESCRIPTION

  • 2 alarm inputs.
  • 2 Remote control outputs.
  • Easy programming of up to 4 telephone numbers / input.
  • Dual band GSM module.
  • Programming SIM card with GSM phone keypad / SMS / PC.
  • Two recorded messages up to 10 seconds / input.
  • Two pre-programmed SMS text messages.
  • Headset for recording / playback messages.
  • Reset input for cancelling dialling.
  • Easy installation and programming.

SPECIFICATION

  • Input Voltage: 9.00 to 35.00 V DC.
  • Activated by N.O., N.C.,+12V DC or GND.
  • Current: 40mA ( idle ), 350mA ( active ).
  • Dimensions: PCB 105 x 80 mm ( boxed 118 x 170 x 30 mm)

 

Click for GSM VAC4 Plus Lite Technical Manual
 
 
 

GSM 10 number Voice and Text Autodialler

GSM Voice / Text Message Alarm Communicator / Autodialler

The GSM Voice Alarm Communicator (GSM-VAC4+) is an inexpensive and reliable device that transmits pre-recorded speech messages and / or SMS text messages, on alarm, to up to 10 different telephone numbers. The GSM network is used for the transmission and is especially suitable for locations where transmission is not possible via fixed telephone or an additional signal path is required. When an input is activated it automatically dials out to pre-programmed numbers and an alarm message is sent. GSM-VAC4 also has 4 outputs to control devices remotely. In addition the New GSM-VAC4+ will send Contact ID format message to an Alarm Receiving Centre.


Description

  • 4 alarm inputs.
  • 4 Remote control outputs.
  • Easy programming of up to 10 telephone numbers / input.
  • Dual band GSM module.
  • Programming into SIM card using GSM telephone keypad. Four recorded messages up to 10 seconds / input.
  • Four pre-programmed SMS text messages.
  • Contact ID mesages to Alarm Receiving Centre.
  • Headset for recording / playback messages.
  • Reset input for cancelling dialling.
  • Easy installation and programming.
  • Listen-In option for alarm verification.

Specification

  • Input Voltage: 12.00 Volts DC. ( 9.00 to 30 Volts DC )
  • Activated by N.O., N.C.,+12V DC or GND
  • Current: 30mA ( idle ), 350mA ( active )
  • Dimensions: PCB 105 x 77 ( boxed 108 x 165 x 56 ) mm

 

GSM 10 number Voice and Text Autodialler Technical Manual
 
 

GSM Digital Communicator
GSM Digital Communicator
Cellular Communication with Audio Verification, Stand Alone or Back Up DigiCell
  • GSM Digital Communicator with Audio Verification
  • Call Hold with Audio Verification
  • Ideal for Installation without PSTN line
  • 4 Programmable Channels
  • Compatible with all networks
  • Benq M23 dual band GSM modem
  • USE to report Line Down and Line Restore on a PSTN Digicom
  • After reporting line down can still report Chan 1 to 3 to C.S. with AV
  • Stand alone or backup system
  • Will integrate with any existing system
  • Complete with its own internal speaker and microphone
  • Internal power supply available with back up battery facility
  • Available with 4 Chan 433 mHz radio Receiver and key fob
 
 

PSTN / GSM INTERFACE UNIT

GSM Back-Up for standard PSTN telephone line
Stand-alone telecommunication unit (instead of PSTN line)
Money saver in offices; GSM to GSM calls from desk phone ( Fixed Cellular Terminal )

VM3 can also be used in connection with different telephone equipment such as:
Alarm panels with built in digital communicator
Automatic voice, digital or signal telephone diallers
Standard telephone sets
PABX - private telephone exchanges
 

FEATURES:

  • Built-in GSM module
  • Interface between telephone equipment and GSM network
  • Transmits all data from Alarm control panel  (ID protocol, SIA)
  • Easy programming (SIM card in your GSM phone)
  • 2 LED monitoring
  • Anti-tamper switch
  • Standards: EMC 89/336 and CEI-79-2
  • 3 alarm inputs - 3 SMS messages
  • 2 service messages: - refill your SIM card (programmable time)
  • periodic test (1h - 240) message

APPLICATION:

  • Back-up security for standard PSTN line
  • Standalone unit instead of PSTN line
  • Money saver in offices - GSM to GSM calls from desk phone

TECHNICAL FEATURES

  • Power supply 12-16V DC, optional back-up battery 12V/1.2Ah
  • Current consumption : 60mA stand-by, 350mA transmitting-operating
  • PCB size in mm: 98×125
  • Box size in mm:  114×218×36
Click for PSTN/GSM Interface Technical Manual                                   

GSM Autodialler connected to Alarm Control Panel.

Easily installed in property - uses wireless PIR's, door/window contacts, panic buttons, smoke detectors and external PIR's. 

Ideal for holiday cottages, properties where no fixed telephone system is available or a second backup system is required.

 
 

GSM Autodialler and R1B Single Zone Receiver          

Easily installed in property - uses wireless PIR's, door/window contacts, panic buttons, smoke detectors and external PIR's.

Ideal for stables, barns, remote buildings and properties where no mains power supply is available. Powered by 85Ah leisure battery. Battery life approximately 1 month between charges.

Detector to receiver maximum transmission range, 500m line of sight. May be extended by use of High gain aerial.

Back | Top of page | Email for details and prices


terms | design by scott